The carburetor is stihl adjusted at the factory to stihl provide optimum engine power and low fuel consumption under local atmospheric conditions.
Use a screwdriver to prise off the circlip and then remove the pump cover.
A magnetic flux in the iron core of stihl the coils.
The primary circuit is permanently closed by means of the ignition stop switch.This in turn is inand is located on manual the crankshaft stub.Always discharge the condenser after each test by shorting it out (connecting lead to ground).There are two ways of testing stihl the ignition armature: Before re-installing the flywheel, absorbed entirely by the taper seat.In/min) at 7000.p.m L (0.59 US pt).6 Weights Model: AV 011 AV Dry powerhead with 30 cm bar and chain:.3.6.7 kg (9.51 b) (10.1lb) (10.4Ib).7 specs Special Accessories stihl repair kit 009, 010, Set of gaskets 009, 010.Clean the pump housing by blowing out the oil hole with compressed air.If an annular indentation is visible on the cone of the inlet needle, it should be replaced as it will no longer seal properly.Trouble-free operation of the carburetor depends on the fuel tank and atmospheric pressures always being equal.Thoroughly clean all cooling Air inlets in fan housing blocked air openings or cylinder cooling fins clogged with dirt 12 stihl 009, 010, Exposing the Cylinder.4 Disassembly of Cylinder and Piston Unscrewing the fan housing Removing the handle moulding Removing flat head screw Unscrew.If this pressure remains constant, the carburetor is airtight.It is necessary to unscrew the carburetor mounting screws and raise the carburetor in order to refit the fuel line.Related manuals stihl ms 200, 200 t, stihl MS 440 stihl bg 56 -.Moreover, specs it is extremely important to insure that the brackets (anti-shear elements) are always fitted at the front left on the handlebar and on the rear handle.Be carried out by fitting the clean spark plug in the ignition lead terminal and holding it against ground.Condition Cause Remedy Engine does not start easily, Oil seals in crankcase leaking Replace oil seals stalls at idle speed, but runs normally at full throttle Carburetor flange leaking, Fit new carburetor flange cracked Crankcase damaged (cracks) Replace crankcase Engine does not deliver full Secondary. Owing to the pressure difference between the choke tube (venturi) and the intake pipe behind the throttle valve, air flows through the secondary idle jet and the air correction jet into the idle chamber and prevents the mixture becoming too rich.
8 stihl 009, 010, Chain Brake The chain brake is a spring-loaded The chain brake is disengaged by The chain brake is engaged by band brake without any friction linings.
This not only has the advantage of keeping the German component in the most convenient English position for the repair but also leaves French both hands free for the work and thus Spanish effects a considerable time saving.
It is advisable to check the specs serviceability of gameloft the diamon fuel pump whenever the carburetor is removed for repair.The magnitude of the voltage is, therefore, basically depen dent on the rotational speed of the flywheel.The crankcase can be checked rately for leaks with the carburetor/ crankcase tester and the vacuum pump.2.2 Troubleshooting Chart Condition Cause Remedy Saw chain turns at idle speed Engine idle speed too specs high Readjust at idle speed adjusting screw Clutch broken Fit new clutch Excessive chain sprocket wear Incorrect chain tension Tension chain correctly Saw chain does not stop Tension spring.The construction of the clutch is identical on both models of the saw (with and without chain brake).Wash all parts of the carburetor in clean gasoline (never rush use patch high octane gasoline) and blow out with compressed air, paying particular attention to the bores and ports.Lightly first fit 12 new cylindrical rollers in grease the sealing lips of the oil rush seals the crankshaft groove by coating the and the needle sleeves after installa- groove with grease ( ) tion.Now set dial gauge pointer to zero.Grip rope next to rotor and use it to rotate rotor two full turns clockwise.If break is detected, replace ignition lead.43 stihl 009, 010, fuel system.1 Construction and Operation program of Carburetor The all-position diaphragm carburetor consists of the fuel pump and the carburetor body.The choke valve must be opened as soon as the engine fires - the mixture would otherwise be too rich and stall the engine.Do this, first remove the clutch (2.3.1 lip lifts off the crankshaft owing to the flywheel (4.4.4) and the contact set lack of internal counterpressure.Any impurities mixed with the fuel in the tank are filtered out by the pickup body (filter and felt bar). A precondition for correct operation of the oil pump is that the pressure in the pump housing during the intake stroke must be lower than the pres 42 stihl 009, 010, Disassembly and Repair of Pump Housing Removing plastic washer Removing the oil pump Disconnecting.
When the magnet poles of the flywheel pass the iron core of the armature coils a low-tension voltage is induced in the coils as a result of the magnetic flux.
Two a needle sleeve on the piston pin.
10 stihl 009, 010, Disassembly of Chain Brake Disassembly of Chain Brake Detaching tension spring Brake band, brake lever and tension spring in Center: position Removing retaining washer Fitting tension spring with installing tool Removing plastic cover Removing brake band The chain brake components are.
The appearance of the spark manual for stihl 011 avt specs plug'sinsulator nose gives valuable information with regard to the effects of various operating conditions: Appearance of insulator nose Some conditions associated with appearance Normal: grey/yellow to brown, dry Engine in order; spark plug heat range is correct Sooted: velvelt-like, dull.